Eaton MTA2V2722L-2R2-R 2.2 uH Through-Hole Inductor 0.72 mOhm
Eaton MTA2V2722L-2R2-R 2.2 uH Through-Hole Inductor 0.72 mOhm

Eaton MTA2V2722L-2R2-R 2.2 uH Through-Hole Inductor 0.72 mOhm

Share
MTA2V2722L-2R2-R: molded through-hole power inductor, 2.2 uH , 57 A Irms, Isat 70 A, DCR 0.72 mOhm.
    • Product Details
    • Download

    Eaton MTA2V2722L-2R2-R 2.2 uH Through-Hole Inductor 0.72 mOhm

    MTA2V2722L-2R2-R at a glance: molded through-hole power inductor, 2.2 uH , 57 A Irms, Isat 70 A, DCR 0.72 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMTA2V2722L-2R2-R
    Inductance2.2 uH
    FLL minimum (at Isat)1.41 uH
    DCR typical @ +20 °C0.72 mOhm
    DCR maximum @ +20 °C0.83 mOhm
    Irms (DC, 40 °C rise)57 A
    Irms266 A
    Isat70 A
    Isat290 A
    SRF typical28.8 MHz
    K-factor21.3
    MountingThrough-hole
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1402

    Mechanical Dimensions & Pad Layout

    MTA2V2722L-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1402: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    A molded through-hole power inductor: the winding is pressed into a magnetic body with leads formed for plated holes. The molding contains the field and the leads carry heat into the board, which is how this family reaches high current in a small volume.

    At 57 A the winding dissipates about 2.34 W in copper using the typical DCR of 0.72 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 5390 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 28.8 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 21.3 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MTA2V2722L family this is value 1 of 2, in a range from 2.2 uH to 3.5 uH.

    Positioning in the Range

    The MTA family is the molded through-hole high-current range: AEC-Q200 qualified, with two Irms and two Isat columns for thermal and transient checks.

    • Through-hole joints carry the full current. Check the solder joint and barrel against the rating, not just the body.
    • Typical applications: infotainment and cluster electronics; audio subsystem: head unit and trunk amp; digital instrument cluster; electronic stability control system (esc); engine and powertrain systems.
    • Design note: check the joint temperature in the thermal test, not the body temperature.

    Frequently Asked Questions

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    What is the SRF column for?
    It marks where the winding capacitance takes over. Keep the switching frequency and its harmonics below it.

    Why two Irms and two Isat columns?
    The datasheet gives both a typical and a maximum condition for each limit, so the thermal and the transient margins can be checked against the worst case.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products