Eaton MTA2V2726H-3R3-R 3.3 uH AEC-Q200 THT Inductor
Eaton MTA2V2726H-3R3-R 3.3 uH AEC-Q200 THT Inductor

Eaton MTA2V2726H-3R3-R 3.3 uH AEC-Q200 THT Inductor

Share
MTA2V2726H-3R3-R: molded through-hole power inductor, 3.3 uH , 67 A Irms, Isat 100 A, DCR 0.63 mOhm.
    • Product Details
    • Download

    Eaton MTA2V2726H-3R3-R 3.3 uH AEC-Q200 THT Inductor

    MTA2V2726H-3R3-R at a glance: molded through-hole power inductor, 3.3 uH , 67 A Irms, Isat 100 A, DCR 0.63 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMTA2V2726H-3R3-R
    Inductance3.3 uH
    FLL minimum (at Isat)2.11 uH
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.72 mOhm
    Irms (DC, 40 °C rise)67 A
    Irms276 A
    Isat100 A
    Isat2128 A
    SRF typical22.3 MHz
    K-factor17
    MountingThrough-hole
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1402

    Mechanical Dimensions & Pad Layout

    MTA2V2726H-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1402: outline with
    rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is an automotive high-current molded inductor with through-hole terminals. The data sheet quotes two Irms columns and two Isat columns, which lets the thermal and the transient limits be checked independently.

    At 67 A the winding dissipates about 2.83 W in copper using the typical DCR of 0.63 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 16500 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 22.3 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 17 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MTA2V2726H family this is value 1 of 2, in a range from 3.3 uH to 6.8 uH.

    Series Positioning

    The MTA family is the molded through-hole high-current range: AEC-Q200 qualified, with two Irms and two Isat columns for thermal and transient checks.

    • Through-hole joints carry the full current. Check the solder joint and barrel against the rating, not just the body.
    • Typical applications: infotainment and cluster electronics; audio subsystem: head unit and trunk amp; digital instrument cluster; electronic stability control system (esc); engine and powertrain systems.
    • Design note: check the joint temperature in the thermal test, not the body temperature.

    Frequently Asked Questions

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    Why two Irms and two Isat columns?
    The datasheet gives both a typical and a maximum condition for each limit, so the thermal and the transient margins can be checked against the worst case.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message