Eaton MTA2V2726L-3R3-R 3.3 uH Through-Hole Inductor 0.63 mOhm
Eaton MTA2V2726L-3R3-R 3.3 uH Through-Hole Inductor 0.63 mOhm

Eaton MTA2V2726L-3R3-R 3.3 uH Through-Hole Inductor 0.63 mOhm

Share
MTA2V2726L-3R3-R: molded through-hole power inductor, 3.3 uH , 67 A Irms, Isat 75 A, DCR 0.63 mOhm.
    • Product Details
    • Download

    Eaton MTA2V2726L-3R3-R 3.3 uH Through-Hole Inductor 0.63 mOhm

    MTA2V2726L-3R3-R at a glance: molded through-hole power inductor, 3.3 uH , 67 A Irms, Isat 75 A, DCR 0.63 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMTA2V2726L-3R3-R
    Inductance3.3 uH
    FLL minimum (at Isat)2.11 uH
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.72 mOhm
    Irms (DC, 40 °C rise)67 A
    Irms276 A
    Isat75 A
    Isat2100 A
    SRF typical23.4 MHz
    K-factor17
    MountingThrough-hole
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1402

    Outline Drawing

    MTA2V2726L-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1402: outline with
    rated mm dimensions, pad layout and marking.

    How to Read These Ratings

    Through-hole mounting here is a thermal decision as much as a mechanical one: the leads take the heat into the copper, and the body can be larger than a reflow part because there is no standoff constraint.

    At 67 A the winding dissipates about 2.83 W in copper using the typical DCR of 0.63 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 9281 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 23.4 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 17 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MTA2V2726L family this is value 1 of 2, in a range from 3.3 uH to 13 uH.

    What This Family Is For

    The MTA family is the molded through-hole high-current range: AEC-Q200 qualified, with two Irms and two Isat columns for thermal and transient checks.

    • Through-hole joints carry the full current. Check the solder joint and barrel against the rating, not just the body.
    • Typical applications: infotainment and cluster electronics; audio subsystem: head unit and trunk amp; digital instrument cluster; electronic stability control system (esc); engine and powertrain systems.
    • Design note: check the joint temperature in the thermal test, not the body temperature.

    Frequently Asked Questions

    Is the body shielded?
    The molding encloses the winding, so the external field is small.

    Is the body shielded?
    The molding encloses the winding, so the external field is small.

    What is the SRF column for?
    It marks where the winding capacitance takes over. Keep the switching frequency and its harmonics below it.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products