Eaton SDCHA1V6045-3R6-R 3.6 uH Semi-Shielded Automotive Inductor
Eaton SDCHA1V6045-3R6-R 3.6 uH Semi-Shielded Automotive Inductor

Eaton SDCHA1V6045-3R6-R 3.6 uH Semi-Shielded Automotive Inductor

Share
SDCHA1V6045-3R6-R: AEC-Q200 semi-shielded inductor, 3.6 uH ±20%, 4.9 A Irms, Isat 7.4 A, DCR 22.5 mOhm.
    • Product Details
    • Download

    Eaton SDCHA1V6045-3R6-R 3.6 uH Semi-Shielded Automotive Inductor

    SDCHA1V6045-3R6-R at a glance: AEC-Q200 semi-shielded inductor, 3.6 uH ±20%, 4.9 A Irms, Isat 7.4 A, DCR 22.5 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberSDCHA1V6045-3R6-R
    Inductance3.6 uH ±20%
    FLL minimum (at Isat)2.02 uH
    DCR typical @ +20 °C22.5 mOhm
    Irms (DC, 40 °C rise)4.9 A
    Isat7.4 A
    SRF typical42 MHz
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1096

    Dimensions and Pad Layout

    SDCHA1V6045-3R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1096: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    Automotive DC-DC stages ask for qualified construction and predictable saturation at the hot corner. This family provides both, with a semi-shielded body that keeps the profile low and the DCR moderate.

    At 4.9 A the winding dissipates about 0.54 W in copper using the typical DCR of 22.5 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 98.6 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 42 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    Within the SDCHA1V6045 family this is value 7 of 20, in a range from 1 uH to 100 uH.

    What This Family Is For

    The SDCA family is the automotive semi-shielded range: the same construction as the commercial parts, qualified to AEC-Q200 and characterised across the temperature range.

    • Qualification covers the part, not the module. The thermal design of the board is still the engineer’s job.
    • Typical applications: led lighting; advanced driver assistance systems (adas); adaptive cruise control (acc); collision avoidance; infotainment and cluster electronics.
    • Design note: use the maximum DCR at the hot corner for the loss budget, and Isat at the same temperature for the transient.

    Frequently Asked Questions

    What is the FLL column for?
    Full-load inductance at saturation current. Use it for the ripple calculation at maximum load rather than the zero-bias value.

    Is the part fully shielded?
    It is semi-shielded: a magnetic resin over the winding. That is adequate for most module layouts but is not a closed metal shield.

    How do I check the hot corner?
    Use Isat at the highest operating temperature and the maximum DCR at that temperature. The room-temperature row is the optimistic one.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message