Eaton SS-5-3.15A-AP 3.15 A 250 Vac Time-Delay Subminiature Fuse
Eaton SS-5-3.15A-AP 3.15 A 250 Vac Time-Delay Subminiature Fuse

Eaton SS-5-3.15A-AP 3.15 A 250 Vac Time-Delay Subminiature Fuse

Share
Eaton SS-5-3.15A-AP is a 3.15 A 250 Vac time-delay subminiature radial fuse, 35 A breaking, 67 A2s I2t.
    • Product Details
    • Download

    Eaton SS-5-3.15A-AP 3.15 A 250 Vac Time-Delay Subminiature Fuse

    SS-5-3.15A-AP at a glance: 3.15 A, 250 Vac, 35 A breaking, 67 A2s I2t, 16.8 mOhm cold - radial leaded, time-delay, rectangular in a UL 94V0 body.

    Key Ratings

    ParameterValue
    Orderable part numberSS-5-3.15A-AP (-AP = 1,000 pcs ammo pack, 12.7 mm pitch)
    BodyRadial leaded, time-delay, rectangular, plastic cap and base, UL 94V0
    Voltage rating250 Vac
    Interrupting rating35 A at rated voltage, 50 Hz
    Typical cold resistance16.8 mOhm
    AgencyUL E19180 (JDYX2/JDYX8) / VDE 40015513 / CCC / KC / SEMKO / PSE+JET
    Dissipation at rating0.20 W
    Typical voltage drop62.5 mV at rated current
    CharacteristicTime-delay (T)
    Current rating3.15 A
    Design standardIEC 60127-3 sheet 4
    I2t, typical melting67 A2s

    At 3.15 A

    • Heat. 62.5 mV at 3.15 A is 0.20 W. The 16.8 mOhm cold figure predicts 0.17 W, so the element sits above its 20 C value - leave margin in a closed adapter.
    • Inrush. A 2 x 3.15 A, 5 ms pulse spends 198.4 mJ, or 0.30 % of the 67 A2s melting integral. That headroom is the point of the T characteristic.
    • Opening. 1.5 In for 60 minutes without opening, 2.1 In within 2 minutes, 2.75 In in 400 ms to 10 s, 10 In under 150 ms.
    • Voltage. 250 Vac is the ceiling. Above that the arc quenches too slowly for a plastic body.
    • Above 2 A. At 3.15 A the element is thicker and the I2t climbs to 67 A2s. That is real inrush tolerance, but it also means the part protects the wiring rather than a semiconductor downstream.
    • Neighbours. One step down is SS-5-2.5A-AP at 2.5 A, one step up is SS-5-4A-AP at 4 A. I2t goes 40.3 to 87 A2s across that range, so the choice is an inrush-margin decision rather than a resolution one.

    For Procurement

    • Part to order: SS-5-3.15A-AP. If your line needs a different reel, the suffix changes (-AP / -BK / -BK2) but the fuse does not.
    • Agency set: UL E19180 (JDYX2/JDYX8) / VDE 40015513 / CCC / KC / SEMKO / PSE+JET.
    • Designed to IEC 60127-3 sheet 4.
    • Do not substitute the fast-acting series where this time-delay part is specified - the inrush will open it.

    FAQ

    Is the whole part number required?
    Yes. Eaton's ordering code includes the packaging suffix - the bare rating is not a complete order line.

    What is the breaking capacity?
    35 A at rated voltage. That is low-breaking-capacity, appropriate for equipment-level protection, not a distribution board.

    Can it go in a socket?
    Yes - the BK/PCS holder takes it if field replacement is wanted. Otherwise it sits directly in the PCB.

    Design note: values are typical unless identified as ratings. Verify the current Eaton data sheet 2621 before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message