Eaton STSP84028U120 ESD Suppressor 2.8 V 1.2 pF
Eaton STSP84028U120 ESD Suppressor 2.8 V 1.2 pF

Eaton STSP84028U120 ESD Suppressor 2.8 V 1.2 pF

Share
STSP84028U120: 2.8 V standoff TVS diode array, 4-channel, 1.2 pF per line, SOP-8 (SP8), commercial grade.
    • Product Details
    • Download

    Eaton STSP84028U120 ESD Suppressor 2.8 V 1.2 pF

    STSP84028U120 at a glance: TVS diode array ESD suppressor, 2.8 V standoff, 18 V clamp, 4 channels, 1.2 pF, 1000 W.

    Key Specifications

    ParameterValue
    Orderable part numberSTSP84028U120
    Standoff voltage (VRWM)2.8 V
    Leakage current at VRWM1 uA max
    Peak pulse power, 8/20 us, per line1000 W
    Clamping voltage at 2 A5.5 V
    Clamping voltage at 10 A10 V
    Clamping voltage at 50 A18 V
    Junction capacitance at 1 MHz, per line1.2 pF typ / 2 pF max
    Channels4
    PolarityUnidirectional
    ESD capability, IEC 61000-4-2+/-30 kV contact / +/-30 kV air
    PackageSOP-8 (SP8)
    MountingSurface mount
    Moisture sensitivity levelMSL 3
    Operating junction temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11160

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data 11160. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    What the Numbers Mean

    Array parts are chosen last, after the connector pinout is fixed. The pin that carries the discharge has to reach the array before it reaches the transceiver, and the ground pin of the array has to be the same copper the connector shell ties to.

    At 50 A the clamp sits at 18 V, or 6.43 times the 2.8 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 1000 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    1.2 pF per line is 133 ohms of reactance at 1 GHz and 1,326 ohms at 100 MHz. Low enough that the loading can be ignored on a high speed pair, which is what this capacitance grade is sold for.

    Standing at 2.8 V the part draws at most 1 uA, which is 2.8 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    All 4 lines return through the common ground pin. That is the point of the array: one connection to the connector ground instead of one per line, and clamps that stay within millivolts of each other during the event.

    A diode array is not a fuse and not a filter. It conducts for the duration of the transient, folds the pulse down to its clamping voltage, and returns to a leakage current measured in microamps. The energy it absorbs is the pulse current times the clamp, for as long as the pulse lasts.

    Where It Goes on the Board

    On a multi-line bus, put one array at the connector rather than one part per line spread along the board. The lines then share a single ground inductance, and the clamps stay within a few millivolts of each other during the event.

    • A unidirectional array clamps one polarity at the breakdown and the other at a forward drop. That asymmetry is correct on a DC rail and wrong on a differential pair that swings below ground.
    • Breakdown is specified at 1 mA. The spread between minimum and maximum is production tolerance, so the design margin is measured from the minimum, not the typical.

    Frequently Asked Questions

    How many of these parts survive repeated strikes?
    The IEC 61000-4-2 rating is a qualification level, not a life count. The part is expected to take the strike repeatedly at the rated level because the energy per event is small, but a higher level shortens that life.

    Why does the package affect the rating?
    It sets the thermal mass and the lead inductance. The same die in a SOD-523 and a SOT-23 dissipates differently, so the package is part of the electrical choice rather than only a footprint decision.

    Why does the clamp voltage differ from the breakdown voltage?
    Breakdown is measured at 1 mA. The clamp is measured at the pulse current, which can be tens of amps, and the difference is the dynamic resistance of the junction multiplied by that current.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message