Eaton STSP84028UL65 TVS Diode 2.8 V 1000 W
Eaton STSP84028UL65 TVS Diode 2.8 V 1000 W

Eaton STSP84028UL65 TVS Diode 2.8 V 1000 W

Share
STSP84028UL65: 2.8 V standoff TVS diode array, 4-channel, 0.65 pF per line, SOP-8 (SP8), commercial grade.
    • Product Details
    • Download

    Eaton STSP84028UL65 TVS Diode 2.8 V 1000 W

    STSP84028UL65 at a glance: TVS diode array ESD suppressor, 2.8 V standoff, 7.6 V clamp, 4 channels, 0.65 pF, 1000 W.

    Electrical Specifications

    ParameterValue
    Orderable part numberSTSP84028UL65
    Standoff voltage (VRWM)2.8 V
    Breakdown voltage (min / typ / max)3 V
    Leakage current at VRWM0.1 uA max
    Peak pulse power, 8/20 us, per line1000 W
    Clamping voltage at 2 A7.6 V
    Junction capacitance at 1 MHz, per line0.65 pF typ / 1 pF max
    Channels4
    PolarityUnidirectional
    ESD capability, IEC 61000-4-2+/-30 kV contact / +/-30 kV air
    PackageSOP-8 (SP8)
    MountingSurface mount
    Moisture sensitivity levelMSL 3
    Operating junction temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11160

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data 11160. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    Reading the Data Sheet

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    At 2 A the clamp sits at 7.6 V, or 2.71 times the 2.8 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 1000 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    0.65 pF per line is 245 ohms of reactance at 1 GHz and 2,449 ohms at 100 MHz. Low enough that the loading can be ignored on a high speed pair, which is what this capacitance grade is sold for.

    Standing at 2.8 V the part draws at most 0.1 uA, which is 0.28 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    All 4 lines return through the common ground pin. That is the point of the array: one connection to the connector ground instead of one per line, and clamps that stay within millivolts of each other during the event.

    Two numbers decide whether an array fits a port. The standoff voltage has to clear the highest steady level the line can hold, and the clamping voltage at the surge current has to stay under the absolute maximum of the transceiver behind it. Everything else on the data sheet is a consequence of those two.

    Layout and Placement

    Keep the return current under the signal. A discharge leaves through the ground pin, and if that current has to cross the board to find a plane it will couple into everything it passes on the way.

    • The clamping voltage is quoted at one pulse current. Halve the current and the clamp falls by roughly the dynamic resistance times the current, which is why a part chosen for a small surge looks better than its headline number.
    • Breakdown is specified at 1 mA. The spread between minimum and maximum is production tolerance, so the design margin is measured from the minimum, not the typical.

    Frequently Asked Questions

    Why does the package affect the rating?
    It sets the thermal mass and the lead inductance. The same die in a SOD-523 and a SOT-23 dissipates differently, so the package is part of the electrical choice rather than only a footprint decision.

    Can one package protect several lines?
    Yes, that is what the channel count means. The lines share a common ground pin, so the return current of all channels flows through one connection and the clamps track each other during the event.

    Does the array capacitance disturb the signal?
    It loads the line as a capacitor to ground. At 1 pF the reactance is about 160 ohms at 1 GHz and 1.6 kilohms at 100 MHz, which is why the low-capacitance grades are used on high speed pairs and the higher grades on slow buses.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message