Eaton TVSL02V03C011 Bidirectional TVS Diode 0201 (0603 metric)
Eaton TVSL02V03C011 Bidirectional TVS Diode 0201 (0603 metric)

Eaton TVSL02V03C011 Bidirectional TVS Diode 0201 (0603 metric)

Share
TVSL02V03C011: 3 V standoff TVS diode array, 1-channel, 11.5 pF per line, 0201 (0603 metric), commercial grade.
    • Product Details
    • Download

    Eaton TVSL02V03C011 Bidirectional TVS Diode 0201 (0603 metric)

    TVSL02V03C011 at a glance: TVS diode array ESD suppressor, 3 V standoff, 6.3 V clamp, 1 channel, 11.5 pF, 50 W.

    Key Specifications

    ParameterValue
    Orderable part numberTVSL02V03C011
    Standoff voltage (VRWM)3 V
    Breakdown voltage (min / typ / max)4.7 V / 6.7 V / 8.7 V
    Leakage current at VRWM1 uA max
    Peak pulse power, 8/20 us, per line50 W
    Clamping voltage at 1 A, TLP 100 ns (typ)5.4 V
    Clamping voltage at 16 A, TLP 100 ns (typ)6.3 V
    Junction capacitance at 1 MHz, per line11.5 pF typ / 13.5 pF max
    Channels1
    PolarityBidirectional
    ESD capability, IEC 61000-4-2+/-25 kV contact / +/-25 kV air
    Package0201 (0603 metric)
    MountingSurface mount
    Moisture sensitivity levelMSL 1
    Operating junction temperature-55 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1241

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data ELX1241. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    What the Numbers Mean

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    At 16 A the clamp sits at 6.3 V, or 2.10 times the 3 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 50 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    11.5 pF per line is 13.8 ohms of reactance at 1 GHz and 138 ohms at 100 MHz. Small enough for a bus in the hundreds of kilohertz to a few megahertz, and measurable once the line rate reaches tens of megahertz.

    Standing at 3 V the part draws at most 1 uA, which is 3 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    A diode array is not a fuse and not a filter. It conducts for the duration of the transient, folds the pulse down to its clamping voltage, and returns to a leakage current measured in microamps. The energy it absorbs is the pulse current times the clamp, for as long as the pulse lasts.

    Where It Goes on the Board

    Run the protected line through the pad rather than teeing off it. A stub of a few millimetres leaves a reflection that shows up as an eye closure on a fast pair and as a harmless glitch on a slow one, and the same layout serves both.

    • A unidirectional array clamps one polarity at the breakdown and the other at a forward drop. That asymmetry is correct on a DC rail and wrong on a differential pair that swings below ground.
    • The capacitance figure is at zero bias. At the working voltage the junction depletes and the value falls, so the loading on a live bus is lower than the table suggests.

    Frequently Asked Questions

    Can one package protect several lines?
    Yes, that is what the channel count means. The lines share a common ground pin, so the return current of all channels flows through one connection and the clamps track each other during the event.

    Why does the clamp voltage differ from the breakdown voltage?
    Breakdown is measured at 1 mA. The clamp is measured at the pulse current, which can be tens of amps, and the difference is the dynamic resistance of the junction multiplied by that current.

    What happens if the surge exceeds the rating?
    The junction overheats and fails short, which then applies the fault current to the board. A fuse or a series resistor ahead of the array is part of the protection scheme, not an accessory.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message