Eaton TVSL02V05C018 ESD Suppressor 5 V 18 pF
Eaton TVSL02V05C018 ESD Suppressor 5 V 18 pF

Eaton TVSL02V05C018 ESD Suppressor 5 V 18 pF

Share
TVSL02V05C018: 5 V standoff TVS diode array, 1-channel, 18 pF per line, 0201 (0603 metric), commercial grade.
    • Product Details
    • Download

    Eaton TVSL02V05C018 ESD Suppressor 5 V 18 pF

    TVSL02V05C018 at a glance: TVS diode array ESD suppressor, 5 V standoff, 7.4 V clamp, 1 channel, 18 pF, 68 W.

    Electrical Specifications

    ParameterValue
    Orderable part numberTVSL02V05C018
    Standoff voltage (VRWM)5 V
    Breakdown voltage (min / typ / max)7 V / 9 V / 11.5 V
    Leakage current at VRWM1 uA max
    Peak pulse power, 8/20 us, per line68 W
    Clamping voltage at 1 A, TLP 100 ns (typ)6.2 V
    Clamping voltage at 16 A, TLP 100 ns (typ)7.4 V
    Junction capacitance at 1 MHz, per line18 pF typ
    Channels1
    PolarityBidirectional
    ESD capability, IEC 61000-4-2+/-25 kV contact / +/-25 kV air
    Package0201 (0603 metric)
    MountingSurface mount
    Moisture sensitivity levelMSL 1
    Operating junction temperature-55 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1241

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data ELX1241. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    Reading the Data Sheet

    Array parts are chosen last, after the connector pinout is fixed. The pin that carries the discharge has to reach the array before it reaches the transceiver, and the ground pin of the array has to be the same copper the connector shell ties to.

    At 16 A the clamp sits at 7.4 V, or 1.48 times the 5 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 68 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    18 pF per line is 8.8 ohms of reactance at 1 GHz and 88.4 ohms at 100 MHz. Small enough for a bus in the hundreds of kilohertz to a few megahertz, and measurable once the line rate reaches tens of megahertz.

    Standing at 5 V the part draws at most 1 uA, which is 5 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    The capacitance in the table is per line, measured at 1 MHz with zero bias. On a differential pair that capacitance sits across the pair and to ground, which is why the low-capacitance grades exist: the same clamp with a fraction of the loading.

    Layout and Placement

    Run the protected line through the pad rather than teeing off it. A stub of a few millimetres leaves a reflection that shows up as an eye closure on a fast pair and as a harmless glitch on a slow one, and the same layout serves both.

    • A unidirectional array clamps one polarity at the breakdown and the other at a forward drop. That asymmetry is correct on a DC rail and wrong on a differential pair that swings below ground.
    • The capacitance figure is at zero bias. At the working voltage the junction depletes and the value falls, so the loading on a live bus is lower than the table suggests.

    Frequently Asked Questions

    Why does the package affect the rating?
    It sets the thermal mass and the lead inductance. The same die in a SOD-523 and a SOT-23 dissipates differently, so the package is part of the electrical choice rather than only a footprint decision.

    What happens if the surge exceeds the rating?
    The junction overheats and fails short, which then applies the fault current to the board. A fuse or a series resistor ahead of the array is part of the protection scheme, not an accessory.

    Does the array capacitance disturb the signal?
    It loads the line as a capacitor to ground. At 1 pF the reactance is about 160 ohms at 1 GHz and 1.6 kilohms at 100 MHz, which is why the low-capacitance grades are used on high speed pairs and the higher grades on slow buses.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message