Eaton TVSL02V07C006 Bidirectional TVS Diode 0201 (0603 metric)
Eaton TVSL02V07C006 Bidirectional TVS Diode 0201 (0603 metric)

Eaton TVSL02V07C006 Bidirectional TVS Diode 0201 (0603 metric)

Share
TVSL02V07C006: 7 V standoff TVS diode array, 1-channel, 8.5 pF per line, 0201 (0603 metric), commercial grade.
    • Product Details
    • Download

    Eaton TVSL02V07C006 Bidirectional TVS Diode 0201 (0603 metric)

    TVSL02V07C006 at a glance: TVS diode array ESD suppressor, 7 V standoff, 12.8 V clamp, 1 channel, 8.5 pF, 90 W.

    Key Specifications

    ParameterValue
    Orderable part numberTVSL02V07C006
    Standoff voltage (VRWM)7 V
    Breakdown voltage (min / typ / max)7.5 V / 8.8 V / 10.5 V
    Leakage current at VRWM1 uA max
    Peak pulse power, 8/20 us, per line90 W
    Clamping voltage at 1 A, TLP 100 ns (typ)9.2 V
    Clamping voltage at 16 A, TLP 100 ns (typ)12.8 V
    Junction capacitance at 1 MHz, per line8.5 pF typ / 10.3 pF max
    Channels1
    PolarityBidirectional
    ESD capability, IEC 61000-4-2+/-25 kV contact / +/-25 kV air
    Package0201 (0603 metric)
    MountingSurface mount
    Moisture sensitivity levelMSL 1
    Operating junction temperature-55 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1241

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data ELX1241. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    What the Numbers Mean

    A diode array is not a fuse and not a filter. It conducts for the duration of the transient, folds the pulse down to its clamping voltage, and returns to a leakage current measured in microamps. The energy it absorbs is the pulse current times the clamp, for as long as the pulse lasts.

    At 16 A the clamp sits at 12.8 V, or 1.83 times the 7 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 90 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    8.5 pF per line is 18.7 ohms of reactance at 1 GHz and 187 ohms at 100 MHz. Small enough for a bus in the hundreds of kilohertz to a few megahertz, and measurable once the line rate reaches tens of megahertz.

    Standing at 7 V the part draws at most 1 uA, which is 7 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    A diode array is not a fuse and not a filter. It conducts for the duration of the transient, folds the pulse down to its clamping voltage, and returns to a leakage current measured in microamps. The energy it absorbs is the pulse current times the clamp, for as long as the pulse lasts.

    Where It Goes on the Board

    Mount the array on the connector side of any series part, with the ground pin dropped straight into the connector ground plane. The trace from the pin to the array is the only path the discharge takes before the transceiver sees it, so its inductance is part of the clamp.

    • The standoff voltage is a DC figure. A bus that idles at 5 V and swings to 12 V in a fault needs a part rated above 12 V, not above 5 V, or the array conducts on every fault and fails open.
    • Leakage is quoted at the rated voltage and at 25 °C. It roughly doubles every 10 °C, which matters on a rail that sits hot inside an enclosure.

    Frequently Asked Questions

    How is the working voltage chosen?
    Above the highest steady state voltage the line can reach, including the fault levels the standard for that interface allows. Then confirm the minimum breakdown voltage is still above that level, because production spread moves it down.

    How many of these parts survive repeated strikes?
    The IEC 61000-4-2 rating is a qualification level, not a life count. The part is expected to take the strike repeatedly at the rated level because the energy per event is small, but a higher level shortens that life.

    Can one package protect several lines?
    Yes, that is what the channel count means. The lines share a common ground pin, so the return current of all channels flows through one connection and the clamps track each other during the event.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products