Eaton TVSL02V09C005 TVS Diode 9 V 80 W
Eaton TVSL02V09C005 TVS Diode 9 V 80 W

Eaton TVSL02V09C005 TVS Diode 9 V 80 W

Share
TVSL02V09C005: 9 V standoff TVS diode array, 1-channel, 7.5 pF per line, 0201 (0603 metric), commercial grade.
    • Product Details
    • Download

    Eaton TVSL02V09C005 TVS Diode 9 V 80 W

    TVSL02V09C005 at a glance: TVS diode array ESD suppressor, 9 V standoff, 12.3 V clamp, 1 channel, 7.5 pF, 80 W.

    Electrical Specifications

    ParameterValue
    Orderable part numberTVSL02V09C005
    Standoff voltage (VRWM)9 V
    Breakdown voltage (min / typ / max)10 V / 11.8 V / 14 V
    Leakage current at VRWM1 uA max
    Peak pulse power, 8/20 us, per line80 W
    Clamping voltage at 1 A, TLP 100 ns (typ)12.3 V
    Junction capacitance at 1 MHz, per line7.5 pF typ
    Channels1
    PolarityBidirectional
    ESD capability, IEC 61000-4-2+/-25 kV contact / +/-25 kV air
    Package0201 (0603 metric)
    MountingSurface mount
    Moisture sensitivity levelMSL 1
    Operating junction temperature-55 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1241

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data ELX1241. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    Reading the Data Sheet

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    At 1 A the clamp sits at 12.3 V, or 1.37 times the 9 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet. The 8/20 microsecond peak pulse power rating for this part is 80 W per line; the derating curve in the data sheet shortens the allowable current as the pulse gets longer.

    7.5 pF per line is 21.2 ohms of reactance at 1 GHz and 212 ohms at 100 MHz. Small enough for a bus in the hundreds of kilohertz to a few megahertz, and measurable once the line rate reaches tens of megahertz.

    Standing at 9 V the part draws at most 1 uA, which is 9 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    Layout and Placement

    On a multi-line bus, put one array at the connector rather than one part per line spread along the board. The lines then share a single ground inductance, and the clamps stay within a few millivolts of each other during the event.

    • ESD ratings are per IEC 61000-4-2 with the part as the first element the discharge meets. A connector shell or a mounting post that offers an easier path takes the strike instead, and the array never conducts.
    • Peak pulse power is an 8/20 microsecond figure per line. A longer waveform allows less current and a shorter one more; the derating curve in the data sheet converts between them and is the number to use when the surge is not the standard one.

    Frequently Asked Questions

    Why does the clamp voltage differ from the breakdown voltage?
    Breakdown is measured at 1 mA. The clamp is measured at the pulse current, which can be tens of amps, and the difference is the dynamic resistance of the junction multiplied by that current.

    How many of these parts survive repeated strikes?
    The IEC 61000-4-2 rating is a qualification level, not a life count. The part is expected to take the strike repeatedly at the rated level because the energy per event is small, but a higher level shortens that life.

    Why does the package affect the rating?
    It sets the thermal mass and the lead inductance. The same die in a SOD-523 and a SOT-23 dissipates differently, so the package is part of the electrical choice rather than only a footprint decision.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message