Eaton WCLA1005V1-100-R 10 nH RF Chip Inductor, SRF 3900 MHz
Eaton WCLA1005V1-100-R 10 nH RF Chip Inductor, SRF 3900 MHz

Eaton WCLA1005V1-100-R 10 nH RF Chip Inductor, SRF 3900 MHz

Share
WCLA1005V1-100-R: wire wound chip inductor, 10 nH ±5%, Q 25 at 250 MHz, 480 mA rated, DCR 200 mOhm.
    • Product Details
    • Download

    Eaton WCLA1005V1-100-R 10 nH RF Chip Inductor, SRF 3900 MHz

    WCLA1005V1-100-R at a glance: wire wound chip inductor, 10 nH ±5%, Q 25 at 250 MHz, 480 mA rated, DCR 200 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberWCLA1005V1-100-R
    OCL10 nH ±5%
    Q minimum @ test frequency25 @ 250 MHz
    SRF minimum3900 MHz
    DCR maximum @ +25 °C200 mOhm
    Rated current (20 °C rise)480 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.19 x 0.66 mm, 0.60 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10981

    Mechanical Dimensions & Pad Layout

    WCLA1005V1-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10981: outline views
    with rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    The value is small and the current is modest, so the design question is not saturation but Q and self-resonance. Q is quoted at one test frequency and SRF is the point where the winding capacitance takes over; both have to be read against the band the part actually works in.

    At the 480 mA rating the winding drops about 96 mV and dissipates 46.1 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 25 at 250 MHz with self-resonance at 3900 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1005V1 family this is value 25 of 52, in a range from 1 to 120 nH.

    Positioning in the Range

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message