Eaton WCLA1005V1-1R0-R 1 nH RF Chip Inductor, SRF 10000 MHz
Eaton WCLA1005V1-1R0-R 1 nH RF Chip Inductor, SRF 10000 MHz

Eaton WCLA1005V1-1R0-R 1 nH RF Chip Inductor, SRF 10000 MHz

Share
WCLA1005V1-1R0-R: wire wound chip inductor, 1 nH ±10%, Q 13 at 250 MHz, 1360 mA rated, DCR 45 mOhm.
    • Product Details
    • Download

    Eaton WCLA1005V1-1R0-R 1 nH RF Chip Inductor, SRF 10000 MHz

    WCLA1005V1-1R0-R at a glance: wire wound chip inductor, 1 nH ±10%, Q 13 at 250 MHz, 1360 mA rated, DCR 45 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA1005V1-1R0-R
    OCL1 nH ±10%
    Q minimum @ test frequency13 @ 250 MHz
    SRF minimum10000 MHz
    DCR maximum @ +25 °C45 mOhm
    Rated current (20 °C rise)1360 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.19 x 0.66 mm, 0.60 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10981

    Dimensions and Pad Layout

    WCLA1005V1-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10981: outline views
    with rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 1360 mA rating the winding drops about 61.2 mV and dissipates 83.2 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 13 at 250 MHz with self-resonance at 10000 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1005V1 family this is value 1 of 52, in a range from 1 to 120 nH.

    Series Positioning

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products