Eaton WCLA1005V1-1R8-R 1.8 nH Chip Inductor, Q 16
Eaton WCLA1005V1-1R8-R 1.8 nH Chip Inductor, Q 16

Eaton WCLA1005V1-1R8-R 1.8 nH Chip Inductor, Q 16

Share
WCLA1005V1-1R8-R: wire wound chip inductor, 1.8 nH ±10%, Q 16 at 250 MHz, 1040 mA rated, DCR 70 mOhm.
    • Product Details
    • Download

    Eaton WCLA1005V1-1R8-R 1.8 nH Chip Inductor, Q 16

    WCLA1005V1-1R8-R at a glance: wire wound chip inductor, 1.8 nH ±10%, Q 16 at 250 MHz, 1040 mA rated, DCR 70 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA1005V1-1R8-R
    OCL1.8 nH ±10%
    Q minimum @ test frequency16 @ 250 MHz
    SRF minimum6000 MHz
    DCR maximum @ +25 °C70 mOhm
    Rated current (20 °C rise)1040 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.19 x 0.66 mm, 0.60 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10981

    Mechanical Drawing

    WCLA1005V1-1R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10981: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    Ceramic-core wire wound parts hold their value well with DC bias because there is no magnetic material to saturate. Ferrite-core versions give more inductance per size but start to roll off as the bias current rises.

    At the 1040 mA rating the winding drops about 72.8 mV and dissipates 75.7 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 16 at 250 MHz with self-resonance at 6000 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1005V1 family this is value 3 of 52, in a range from 1 to 120 nH.

    Positioning in the Range

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products