Eaton WCLA1005V1-240-R 24 nH Wire Wound Chip Inductor
Eaton WCLA1005V1-240-R 24 nH Wire Wound Chip Inductor

Eaton WCLA1005V1-240-R 24 nH Wire Wound Chip Inductor

Share
WCLA1005V1-240-R: wire wound chip inductor, 24 nH ±5%, Q 25 at 250 MHz, 400 mA rated, DCR 300 mOhm.
    • Product Details
    • Download

    Eaton WCLA1005V1-240-R 24 nH Wire Wound Chip Inductor

    WCLA1005V1-240-R at a glance: wire wound chip inductor, 24 nH ±5%, Q 25 at 250 MHz, 400 mA rated, DCR 300 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCLA1005V1-240-R
    OCL24 nH ±5%
    Q minimum @ test frequency25 @ 250 MHz
    SRF minimum2700 MHz
    DCR maximum @ +25 °C300 mOhm
    Rated current (20 °C rise)400 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.19 x 0.66 mm, 0.60 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10981

    Dimensions and Pad Layout

    WCLA1005V1-240-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10981: outline views
    with rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 400 mA rating the winding drops about 120 mV and dissipates 48 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 25 at 250 MHz with self-resonance at 2700 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1005V1 family this is value 36 of 52, in a range from 1 to 120 nH.

    What This Family Is For

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    What does the rated current mean here?
    It is the current that produces a 20 °C self-temperature rise, not a saturation limit. On a ceramic-core part there is no saturation to speak of, so the thermal figure is the only limit.

    Why choose wire wound over multilayer?
    Q. A wound coil has lower resistance for the same inductance, so Q is higher and the loss in a filter or matching network is lower. The price is size and cost, which is why multilayer parts dominate pure decoupling.

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message