Eaton WCLA1608V1-330-R 33 nH Inductor, 600 mA Rated
Eaton WCLA1608V1-330-R 33 nH Inductor, 600 mA Rated

Eaton WCLA1608V1-330-R 33 nH Inductor, 600 mA Rated

Share
WCLA1608V1-330-R: wire wound chip inductor, 33 nH ±5%, Q 36 at 250 MHz, 600 mA rated, DCR 220 mOhm.
    • Product Details
    • Download

    Eaton WCLA1608V1-330-R 33 nH Inductor, 600 mA Rated

    WCLA1608V1-330-R at a glance: wire wound chip inductor, 33 nH ±5%, Q 36 at 250 MHz, 600 mA rated, DCR 220 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberWCLA1608V1-330-R
    OCL33 nH ±5%
    Q minimum @ test frequency36 @ 250 MHz
    SRF minimum2300 MHz
    DCR maximum @ +25 °C220 mOhm
    Rated current (20 °C rise)600 mA
    OCL test frequency250 MHz
    OCL test voltage500 mV
    Package1.78 x 1.10 mm, 0.95 mm high
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10982

    Dimensions and Pad Layout

    WCLA1608V1-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10982: outline views
    with rated mm dimensions, pad layout and marking.

    Reading the Data Sheet

    This is a wire wound chip inductor for RF and small-signal circuits: tight tolerance, defined Q, and a rated current that is set by a 20 °C self-temperature rise rather than by saturation.

    At the 600 mA rating the winding drops about 132 mV and dissipates 79.2 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 36 at 250 MHz with self-resonance at 2300 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCLA1608V1 family this is value 17 of 31, in a range from 1.6 to 470 nH.

    Series Positioning

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Is the automotive version electrically different?
    The construction is the same; the qualification and the temperature range are not. The WCLA parts are AEC-Q200 qualified and rated to +125 °C, the commercial WCL parts to +85 °C.

    What happens above the self-resonant frequency?
    The winding capacitance dominates and the part behaves capacitively. Keep the working band, and the harmonics that carry energy, below SRF.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message